To string an electric guitar, remove the old strings, thread each new string through the bridge, feed it through the tuner post, kink it and wind it down the post with about three turns, then stretch it and tune it until the pitch stops dropping. Most people can do the job in 20 to 30 minutes with a set of strings, a winder, cutters and a tuner. If you would rather have it done properly, our in-store restring service in Huntingdon takes the whole thing off your hands.
This guide covers a standard fixed-bridge or tremolo electric guitar, then the extra steps for a Floyd Rose-style locking tremolo. It also covers the two things that decide whether the job goes well: how you wind the string and how you stretch it.
Table of Contents
- What you need before you start
- Know the string order
- Step 1: Take off the old strings
- Step 2: Thread the string through the bridge
- Step 3: Cut to length and wind without slipping
- Step 4: Stretch the strings and tune
- Locking tremolo and Floyd Rose guitars
- Common mistakes and how to fix them
- How often should you change your strings?
- Why we think a proper restring is worth it
- Let us restring it for you
- FAQ
- Sources
What you need before you start
The kit is small. Guitar World’s restringing guide lists a fresh set of strings, a string winder, sturdy wire cutters and a tuner. MusicRadar’s tech guide adds a small flat-headed screwdriver, which is handy for bending down cut string ends.
- Strings. Buy the gauge you already use unless you are changing on purpose. A set labelled 10-46 is a common choice for electrics; lighter sets such as 9.5-44 feel easier to bend, and heavier ones such as 10-52 suit lower tunings and heavier playing. Our guide to choosing an electric string gauge explains the trade-offs. You can browse sets in our guitar strings collection, including Elixir 10-46 Nanoweb coated strings, D’Addario EXL120+ 9.5-44 and D’Addario EXL140 10-52.
- A string winder. It turns the tuner far faster than your fingers. Our roundup of home setup tools covers the options for quick string changes.
- Wire cutters. Guitar World points out that scissors will not cut guitar strings cleanly and will blunt. Use proper cutters.
- A tuner. A clip-on tuner or a tuner app is fine.
- A soft cloth. For wiping the fretboard and body while the strings are off.
If your guitar has a Floyd Rose-type locking tremolo, Guitar World also lists a 3 mm hex (Allen) key and a slim wooden stick to hold the bridge up. More on that below.
Know the string order
On a standard six-string, the thickest string is the lowest in pitch and sits nearest your face when you hold the guitar to play. From thickest to thinnest the strings are E, A, D, G, B and E, numbered 6 to 1. Your set will come in individually labelled envelopes or with a chart. The three thickest strings (6, 5 and 4) and often the fourth are wound with metal wire; the two thinnest are plain steel, and the G is plain in most sets.
On most electric guitars, the tuners for the three lowest strings sit on one side of the headstock and the three highest on the other, or all six on one side, depending on the design. Look at where each string runs before you remove anything.

Step 1: Take off the old strings
Worn strings are worth replacing. Guitar World notes that old strings go dull from grime and become deformed, most obviously the wound strings, which get dented where they meet the frets.
One at a time or all at once? Changing one string at a time keeps tension on the neck and the bridge in place, and it is the easiest way to keep track of the order. Taking all six off lets you clean the fretboard properly. For a first attempt, either works; if you have a tremolo bridge, changing one string at a time is the safer habit because the bridge stays balanced.
On a guitar without a tremolo system, slacken each string with the tuner. A winder speeds this up. Then cut the string, and D’Addario’s published advice, which is widely followed, is to cut near the 12th fret so both halves coil evenly and are easy to pull out. Pull each piece out through the bridge and tuner. Dispose of the old strings safely: the cut ends are sharp.
Clean while the strings are off. With all six removed, wipe the fretboard with a soft cloth and dust under the strings and around the pickups. It is the easiest moment to do it.
Step 2: Thread the string through the bridge
The route depends on the guitar’s bridge:
- Through-body or top-loaded bridge (Telecaster-style, Les Paul-style). Feed the string through the ferrule or the stop-bar tailpiece from the correct side, as the guitar is designed to be strung.
- Tremolo bridge (Stratocaster-style). Thread the string through the hole in the back of the body or, on a top-load model, through the bridge block. The ball end should sit snugly against the block. Make sure the ball end is seated before you pull the string forward.
- Hardtail with string-through body. Push the ball end in from the back, then pull the string out through the bridge saddle.
Pull the string through along the neck and over the saddle, nut slot and on to the tuner, keeping it lined up with its groove in the nut. Check it sits in the right saddle groove; a string running outside its saddle will not intonate properly.
Step 3: Cut to length and wind without slipping
This is the step that decides whether the guitar stays in tune. Too much string on the post and the windings stack up and slip; too little and the string can pull free.
Leave the right amount of slack
Pull the string up to the tuner, then back off a little so there is slack. A common rule of thumb is to leave enough that you can lift the string a couple of centimetres to a few centimetres above the fretboard at the 12th fret, so there is room for about three wraps. Sound on Sound’s Paul White says three turns are usually enough, and too many risks the windings slipping.
The kink-and-wrap method
MusicRadar’s guide describes the method it calls the quickest, best for stability and easiest to de-string:
- Feed the string through the hole in the tuner post.
- Kink the string sharply where it meets the hole.
- Hold the string under tension, and wrap the loose end clockwise around a right-handed tuner, under the kink.
- Bend the loose end up and over the kink, then wind the string under the kink while keeping tension on it.
The extra kink adds another level of stability to the wind, according to MusicRadar. Paul White’s version of the same idea is to bend the string back around itself after it passes through the shaft hole, so that it winds over its own end.
Winding direction and neatness
Make the windings sit neatly, one beside the next, working down the post. Do not let a wind run on top of another. For most tuners the thicker strings should end up lower on the post and the thinner strings higher, which keeps the string angle over the nut straight.
On guitars with Fender-style slotted posts, Paul White suggests cutting the string to length and poking the end down the hole in the middle of the post before winding, which grips it very securely. He also recommends checking that the fixing nuts on the headstock face are reasonably tight, because loose ones cause tuning trouble.
Trim the ends
Cut the excess close to the post. MusicRadar recommends bending the cut ends down with a larger flat-headed screwdriver so they do not puncture fingertips or snag a gig bag.
Step 4: Stretch the strings and tune
New strings stretch. If you tune to pitch and play, they go flat within minutes. Stretching them in at the start saves you from re-tuning constantly.
MusicRadar’s advice is not to tune to pitch straight away. Instead, stretch the strings in with a sensible tug so the pitch drops, repeat until the drop lessens, then do a final tune-up. It also says to expect some re-tuning, because the neck bends forward under string pressure.
Paul White’s routine is easy to follow:
- Tune each string up to pitch.
- Grip it about halfway along and pull it gently away from the body for a few seconds.
- Check the tuning. It will almost certainly have gone flat.
- Tune back up and repeat three or four times per string until it holds.
Tune up to the note rather than down to it. If you overshoot, drop below the pitch and come back up, so the gear and string settle against the tension.
Locking tremolo and Floyd Rose guitars
Floyd Rose-type bridges float and lock, so restringing is a bigger job. Guitar World’s procedure runs like this:
- Loosen the string clamps at the nut with a 3 mm Allen key and store the clamps somewhere safe.
- Prop the bridge up with a lollipop stick or soft timber so it does not drop into the body.
- Drop the pitch, loosen the bridge string clamp blocks and pull the strings out.
- Reset each fine tuner screw to the middle of its travel before tuning, so you can raise and lower pitch with plenty of range.
Guitar World also advises using the same string gauge, or resetting the tremolo tension if you change it. Re-lock the nut only when the strings are at pitch and settled, and do not over-tighten the clamps. Because every string change shifts the tension on the others, expect to go round the guitar several times.
If this sounds like more than you want to take on, you can bring it to us. We offer guitar setups, servicing and repairs, and a floating bridge is exactly the kind of job worth handing to someone with the tools.
Common mistakes and how to fix them
| Problem | Likely cause | Fix |
|---|---|---|
| Guitar keeps going flat | Strings not stretched, too many windings, or loose tuner nuts | Stretch each string three or four times; use about three turns; tighten the nuts on the headstock face |
| String slips on the post | No kink, or windings stacked on one another | Use the kink-and-wrap method and wind neatly downward |
| Pings and slow return to pitch | String sticking in the nut slot | Run the nut-binding test below |
| Sharp cut ends | Ends left long | Trim close and bend them down |
| Strings snap on first tuning | Too much tension or too many wraps | Stretch gently and tune up to pitch |
The nut-binding test
Sound on Sound describes a quick check. Tune a string to pitch, then push down hard on it behind the nut. If the note stays slightly sharp afterwards, the string is sticking in the slot, usually because the slot is too narrow. A wound string can be freed by sawing an old string back and forth in the slot like dental floss. That kind of nut work is where a proper setup pays off.
How often should you change your strings?
There is no single figure. Change strings when they sound dull, feel rough or gritty, will not hold their tuning, or look discoloured. Players who gig or practise daily change them more often than occasional players, and coated strings are designed to stay fresh for longer. Our guide to the best strings for UK players compares electric string types, and it is a good starting point if you are not sure what to buy next.
Why we think a proper restring is worth it
Every guitar that comes through our shop is inspected before it is sold, and we think that habit shapes how we look at strings too. A fresh set on a well-set-up guitar changes how the instrument feels more than almost any other small job.
The winding, stretching and tuning are all things you can learn, and we are happy to help you with that. But a restring is also the best moment to check the nut, the bridge and the tuners, and that is where our setup experience matters. We would sooner see a guitar come in for a restring and leave feeling right than have a player fight with an unstable guitar for months.
If you are buying a new or pre-owned guitar from us, the strings, the setup and the support afterwards all belong together. That is how we like to look after players of every level.
Music
Let us restring it for you
If you would rather not do it yourself, our In-Store Restring Service is available at our shop in Huntingdon, Cambridgeshire. Pick your strings from our guitar strings range, or ask us about a full setup, servicing or repair for the guitar.
If you are looking for your next instrument, our electric guitars include new and pre-owned models, and our accessories cover winders, straps and more. Our guitar cases and gig bags will keep it protected between gigs.
FAQ
Do you need a tool to change guitar strings?
You can do it with your hands and a pair of cutters, but a string winder makes it much quicker. You need wire cutters because scissors will blunt, and a tuner for the final tune-up. A locking tremolo also needs a 3 mm Allen key.
What is the correct order of strings on a guitar?
From the thickest, lowest string to the thinnest, highest string, the order is E, A, D, G, B, E. They are numbered 6 to 1 with the thinnest as string 1. Your set’s envelopes are labelled so you can match each one to its place.
How many times should you wind the string around the tuner?
About three turns is usually enough, according to Sound on Sound. Too many turns can let the windings slip, and too few can let the string pull loose. Wind neatly, downward, with no wrap on top of another.
Why does my guitar keep going out of tune after restringing?
New strings stretch, so they go flat as they settle. Stretch each one by tugging gently, re-tune and repeat until it holds. If it still drifts, check the tuner fixing nuts and the nut slots.
Sources
- How to restring an electric guitar, Guitar World
- A tech explains how to change your electric guitar strings, MusicRadar
- Setting Up Guitar: DIY Maintenance Tips, Sound on Sound












Share:
A Major on Guitar: Notes, Fingerings and Clean Changes